不銹鋼新聞

不銹鋼新聞

您當前的位置: > 不銹鋼新聞 >

不銹鋼鈑金加工的工藝流程介紹

發布日期:2016-01-18 瀏覽次數:文章來源:未知 作者:北京不銹鋼

導讀:奶茶视频成人播放器奶茶视频成人app是集銷售與設計、加工、制作、安裝為一體的鈑金加工廠。本公司在 北京不銹鋼加工 、不銹鋼工程上始終堅持以人為本、質量興業、用戶至上的服務宗旨,以獨到的設計風格、精良的施工質量、規范的工程監控體系、完善的服務標

   奶茶视频成人app是集銷售與設計、加工、制作、安裝為一體的鈑金加工廠。本公司在北京不銹鋼加工、不銹鋼工程上始終堅持以人為本、質量興業、用戶至上的服務宗旨,以獨到的設計風格、精良的施工質量、規范的工程監控體系、完善的服務標準,竭誠為客戶提供最完善、最合理的服務。聯系電話:13718106922 馮經理。
    按鈑金件的基本加工方式,如下料、折彎、拉伸、成型、焊接。 本規范闡述每一種加工方式所要注意的工藝要求。
    圖紙到手后,根據展開圖及批量的不同選擇不同落料方式,其中有激光,數控沖床,剪板,模具等方式,然后根據圖紙做出相應的展開。數控沖床受刀具方面的影響,對于一些異形工件和不規則孔的加工,在邊緣會出現較大的毛刺,要進行后期去毛刺的處理,同時對工件的精度有一定的影響;激光加工無刀具限制,斷面平整,適合異形工件的加工,但對于小工件加工耗時較長。在數控和激光旁放置工作臺,利于板料放置在機器上進行加工,減少抬板的工作量。一些可以利用的邊料放置在指定的地方,為折彎時試模提供材料。在工件落料后,邊角、毛刺、接點要進行必要的修整(打磨處理),在刀具接點處,用平銼刀進行修整,對于毛刺較大的工件用打磨機進行修整,小內孔接點處用相對應的小銼刀修整,以保證外觀的美觀,同時外形的修整也為折彎時定位作出了保證,使折彎時工件靠在折彎機上位置一致,保障同批產品尺寸的一致。

    在落料完成后,進入下道工序,不同的工件根據加工的要求進入相應的工序。有折彎,壓鉚,翻邊攻絲,點焊,打凸包,段差,有時在折彎一兩道后要將螺母或螺柱壓好,其中有模具打凸包和段差的地方要考慮先加工,以免其它工序先加工后會發生干涉,不能完成需要的加工。在上蓋或下殼上有卡勾時,如折彎后不能碰焊要在折彎之前加工好。

    折彎時要首先要根據圖紙上的尺寸,材料厚度確定折彎時用的刀具和刀槽,避免產品與刀具相碰撞引起變形是上模選用的關鍵(在同一個產品中,可能會用到不同型號的上模),下模的選用根據板材的厚度來確定。其次是確定折彎的先后順序,折彎一般規律是先內后外,先小后大,先特殊后普通。有要壓死邊的工件首先將工件折彎到30°—40°,然后用整平模將工件壓死。

    壓鉚時,要考慮螺柱的高度選擇相同不同的模具,然后對壓力機的壓力進行調整,以保證螺柱和工件表面平齊,避免螺柱沒壓牢或壓出超過工件面,造成工件報廢。

    焊接有氬弧焊,點焊,二氧化碳保護焊,手工電弧焊等,點焊首先要考慮工件焊接的位置,在批量生產時考慮做定位工裝保證點焊位置準確。

為了焊接牢固,在要焊接的工件上打凸點,可以使凸點在通電焊接前與平板均勻接觸,以保證各點加熱的一致,同時也可以確定焊接位置, 同樣的,要進行焊接,要調好預壓時間,保壓時間,維持時間,休止時間,保證工件可以點焊牢固。點焊后在工件表面會出現焊疤,要用平磨機進行處理,亞弧焊主要用于兩工件較大,又要連接在一起時,或者一個工件的邊角處理,達到工件表面的平整,光滑。亞弧焊時產生的熱量易使工件變形,焊接后要用打磨機和平磨機進行處理,特別是邊角方面較多。

工件在折彎,壓鉚等工序完成后要進行表面處理,不同板材表面的處理方式不同,冷板加工后一般進行表面電鍍,電鍍完后不進行噴涂處理,采用的是進行磷化處理,磷化處理后要進行噴涂處理。電鍍板類表面清洗,脫脂,然后進行噴涂。不銹鋼板(有鏡面板,霧面板,拉絲板)是在折彎前進行可以進行拉絲處理,不用噴涂,如需噴涂要進行打毛處理;鋁板一般采用氧化處理,根據噴涂不同的顏色選擇不同的氧化底色,常用的有黑色和本色氧化;鋁板需噴涂的進行鉻酸鹽氧化處理后噴涂。表面前處理這樣做可以使清潔表面,顯著提高涂膜附著力,能成倍提高涂膜的耐蝕力。清洗的流程先清洗工件,先將工件掛在流水線上,首先經過清洗溶液中(合金去油粉),然后進入清水中,其次經過噴淋區,再經過烘干區,最后將工件從流水線上取下。

在表面前處理后,進入噴涂工序,在工件要求裝配后噴涂時,牙或部分導電孔需保護處理,牙孔可查入軟膠棒或擰入螺釘,需導電保護的要用高溫膠帶貼上,大批量的做定位工裝來定位保護,這樣噴涂時不會噴到工件內部,在工件外表面能看到的螺母(翻邊)孔處用螺釘保護,以免噴涂后工件螺母(翻邊)孔處需要回牙。一些批量大的工件還用到工裝保護;工件不裝配噴涂時,不需要噴涂的區域用耐高溫膠帶和紙片擋住,一些露在外面的螺母(螺柱)孔用螺釘或耐高溫橡膠保護。如工件雙面噴涂,用同樣方法保護螺母(螺柱)孔;小工件用鉛絲或曲別針等物品竄在一起后噴涂;一些工件表面要求高,在噴涂前要進行刮灰處理;一些工件在接地符處用專用耐高溫貼紙保護。在進行噴涂時,首先工件掛在流水線上,用氣管吹去表面的粘上的灰塵。進入噴涂區噴涂,噴完后順著流水線進入到烘干區,最后從流水線上取下噴涂好的工件。其中還有手工噴涂和自動噴涂兩類,這樣采用的工裝就不同了。

在噴涂之后進入裝配工序,裝配前,要將原來噴涂中用的保護貼紙撕去,確定零件內螺紋孔沒有被撒進漆或粉,在整個過程中,要戴上手套,避免手上灰塵附在工件上,有些工件還要用氣槍吹干凈。裝配好之后就進入包裝環節了,工件檢查后裝入專用的包裝袋中進行保護,一些沒有專用包裝的工件用氣泡膜等進行包裝,在包裝前先將氣泡膜裁成可以包裝工件的大小,以免一面包裝一面裁,影響加工速度;批量大的可定做專用紙箱或氣泡袋、膠墊、托盤、木箱等。包裝好后放入紙箱,然后在紙箱上貼上相應成品或半成品標簽。

鈑金件的質量除在生產制程中嚴格要求外,就是需要獨立于生產的品質檢驗,一是按圖紙嚴格把關尺寸,二是嚴格把關外觀質量,對尺寸不符者進行返修或報廢處理,外觀不允許碰劃傷,噴涂后的色差、耐蝕性、附著力等進行檢驗。這樣可以找到展開圖錯誤,制程中的不良習慣,制程中的錯誤,如數沖編程錯誤,模具錯誤等。文章來源:(http://mglny.com

  Beijing Yi Feng Yuan Da stainless steel decoration Engineering Co., Ltd. is a set sales and design, processing, production, installation as one of the sheet metal processing factory. The company in Beijing stainless steel processing, stainless steel engineering has always adhere to the people-oriented, quality, customer first service purposes, with a unique design style, excellent facilities
Work quality, standard engineering monitoring system, perfect service standards, dedicated to provide customers with the most perfect, the most reasonable service. Tel: 13718106922 Feng manager.
According to the basic processing of sheet metal parts, the following materials, bending, stretching, forming, welding. This specification describes each processing mode should pay attention to the process requirements.
After drawing the hand, according to the start of the map and the volume of different choice of different materials, including laser, CNC punch, shear plate, mold, etc., and then make the corresponding expansion according to the drawings. CNC punching machine by the impact of the tool, for some special shaped workpiece and irregular hole machining, the edge will appear larger
Burr, late deburring processing. At the same time, the precision of the workpiece has certain influence; laser processing without limit of the cutting tool and flat section, suitable for irregular workpieces processing, but for small workpiece is time-consuming. In the numerical control and laser side placed on the table, which is conducive to the plate placed on the machine for processing, reduce
Lifting plate load. Some can use the material placed in the designated place, provide materials for bending test. In the blanking workpiece, edges, burrs, and contact to were necessary dressing (polished), at the junction of the tool, use a flat file trimming, for burr larger workpiece with grinding machine repair
, small contact holes should be relatively small file trimming, to ensure the appearance of beautiful, also shape the dressing also for bending positioning assurances, bending workpiece by consistent position on the bending machine, products from the same batch size consistent with the security.
Upon completion of the blanking, into the next process, different parts according to the requirements of the processing into the corresponding process. A bending, pressure riveting, flange tapping, spot welding, convex hull, difference, sometimes in bending one or two must be nuts or studs well pressure, which has mold hit convex hull and a place to consider first processing, lest
Other working procedures will interfere with the processing, can not complete the required processing. When the upper cover or the lower shell is provided with a clamping hook, the welding machine can not be touched to be welded after bending.
To avoid bending should be the first to according to the drawings on the size and the thickness of the material to determine the bending with the tool and cutter groove, products and tool collision deformation caused by is mold selected key (in the same product, may use different types of upper die), mode selection according to the thickness of the plate to determine. The second is true
The order of the bending and bending, the general rule is the first inside and outside, the first small after the big, first special after the general. Have to edge the workpiece on workpiece bending to 30 degrees, 40 degrees, and then the workpiece crushed with leveling die.
Pressure riveting, to consider the height of stud to choose the same different mold, then the pressure on the press adjusted to ensure the stud and the workpiece surface flush, avoid stud no pressure in prison or press over the workpiece surface, causing workpiece scrapped.
Welding with argon arc welding, spot welding, carbon dioxide arc welding, manual arc welding and so on, spot welding should first consider the location of the workpiece welding, in mass production, consider making the positioning tool to ensure accurate spot welding position.
To welding firm, on the workpiece to be welded hit bump, bump in energized before welding and flat uniform contact, to ensure a uniform heating of each point. At the same time, it can determine the position of welding, the same to welding, to adjust the preloading time, holding pressure time, maintenance time, rest time, ensure workpiece
Firmly to spot welding. After spot welding on the surface of the workpiece will appear welding scar, flat grinding machine used for processing and sub arc welding is mainly used for two workpiece is larger, but also connected together, or a workpiece edge angle processing, achieve the flatness of workpiece surface, smooth. The heat produced in the sub arc welding is easy to deform the workpiece, and the welding is to be used after welding.
Mill and mill for processing, especially in the side corner.
Workpiece in bending and pressure riveting process is completed to surface treatment, sheet with different surface treated in a different way, cold plate processing generally surface plating, electroplating after spraying, the is phosphating treatment and phosphating treatment to spray processing. Electroplating plate type surface cleaning, skim, ran
After spraying. Stainless steel plate (with a mirror panel, fog panel, drawing board) is in front of the bending drawing can be processed and do not spray, such as the need to spray to beat hair treatment; aluminum by oxidation treatment, according to different oxidative color choice different color spraying, commonly used are black and ecru oxidation;
The need for spraying aluminum chromate oxidation coating. Surface pre-treatment to do so can make the cleaning surface, significantly improve the film adhesion, can increase the corrosion resistance of the coating. The cleaning process before cleaning the workpiece, the workpiece hanging on the assembly line, first through the cleaning solution (alloy degreasing powder), and then into the
Into the water, followed by the spray area, and then through the drying area, and finally removed the workpiece from the assembly line.
After the surface pretreatment, into the spraying process, in the requirements of the workpiece assembly after spraying, teeth or partially conductive holes need the protection of the and documented of the tooth hole into the soft rod or screw in the screw, conductive protection to paste with high temperature adhesive tape on, large quantities of do

熱點推薦

  • 不銹鋼廣告牌-2
  • 不銹鋼樓梯扶手-1
  • 不銹鋼廣告牌-2
  • 不銹鋼感應門3
  • 不銹鋼感應門2
  • 不銹鋼廣告牌-3
  • 相關閱讀

  • 不銹鋼架中留下的指紋處理和好處
  • 不銹鋼加工20190511
  • 不銹鋼加工2018年12月25日
  • 不銹鋼加工產品容易變形怎么辦
  • 北京怡豐源達不銹鋼加工廠開工了,歡迎來點
  • 北京不銹鋼加工廠中不銹鋼常見的焊接方式
  • 不銹鋼新聞   NEWS
    奶茶视频成人播放器   Contact Us